Simulate a 12-term calibration and initialize all coefficients. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
A120
A8R
Description
Simulate a One-Path Two-Port Reverse Calibration. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
A8R
A8T
Description
Simulate a One-Path Two-Port Forward Calibration. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
A8T
ABORTCAL
Description
Aborts the current RF or Hardware Calibration.
If the instrument is in the middle of a calibration such as hardware, linear power, or flat power calibration, a DCL (DEVICE CLEAR) bus command must first be issued to change the parser from execute mode to parsing mode
A DCL is not normally required if the calibration type is an RF calibration.
After the DCL command, the ABORTCAL command can be issued to abort the current calibration process. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
ABORTCAL
ABT
Description
Simulate a Transmission Frequency Response Both Paths Calibration. No query.
Query only. Output s parameter or user defined parameter.
Query Parameters
<NRf> = Selected trace number.
Output
<NR1>
Syntax
CHSXX? <NRf>
CHTDDIST? <NRf>
Description
Query only. Output the time domain parameter distance/time.
Query Parameters
<NRf> = Selected trace number.
Output
<NR1>
Syntax Example
CHTDDIST? <NRf>
CHTDPIX? <NRf>
Description
Query only. Output the time domain phasor impulse on/off status.
Query Parameters
<NRf>
Output
<NR1>
Where:
• 0 for Off
• 1 for On
Syntax Example
CHTDPIX? <NRf>
CHTDX? <NRf>
Description
Query only. Output domain mode.
Query Parameters
<NRf>
Output
<NR1>
Syntax Example
CHTDX? <NRf>
CHX?
Description
Query only. Output active trace number.
Query Parameters
NA
Output
<NR1>
Syntax Example
CHX?
CL0 <NRf>
CL0?
Description
Enter inductive coefficient 0 for short. Output inductive coefficient 0 for short.
Cmd Parameters
<NRf>
Query Parameters
NA
Output
<NR3>
Syntax Example
CL0 <NRf>
CL0?
CL1 <NRf>
CL1?
Description
Enter inductive coefficient 1 for short. Output inductive coefficient 1 for short.
Cmd Parameters
<NRf>
Query Parameters
NA
Output
<NR3>
Syntax Example
CL1 <NRf>
CL1?
CL2 <NRf>
CL2?
Description:
Enter inductive coefficient 2 for short. Output inductive coefficient 2 for short.
Cmd Parameters
<NRf>
Query Parameters
NA
Output
<NR3<
Syntax Example
CL2 <NRf>
CL2?
CL3 <NRf>
CL3?
Description
Enter inductive coefficient 3 for short. Output inductive coefficient 3 for short.
Cmd Parameters
<NRf>
Query Parameters
NA
Output
<NR3>
Syntax Example
CL3 <NRf>
CL3?
CLB
Description
Clear all multiple source band definitions. No query.
Syntax Example
CLB
Cmd Parameters
NA
Output
NA
Syntax Example
CLB
CLBMM
Description
Clear the new MMWave band definitions. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
CLBMM
CM1
Description
Select male 1.0 mm connector for current port. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
CM1
CM2
Description
Select male 2.4 mm connector for current port. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
CM2
CM3
Description
Select male GPC-3.5 connector for current port. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
CM3
CM716
Description
Select male 7/16 connector for current port. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
CM716
CMC
Description
Select male TNC connector for current port. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
CMC
CMK
Description
Select male K connector for current port. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
CMK
CMN
Description
Select male Type N connector for current port. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
CMN
CMN75
Description
Select male Type N 75 Ohm connector for current port. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
CMN75
CMS
Description
Select male SMA connector for current port. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
CMS
CMSP
Description
Select special male connector for current port. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
CMSP
CMV
Description
Select male V connector for current port. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
CMV
CMX?
Description
Query only. Output the calibration method.
Query Parameters
NA
Output
<NR1> 1|2|3
Where:
• 1 for Standard OSL
• 2 for Offset-Short
• 3 for LRL/LRM
Syntax Example
CMX?
CND
Description
Select user specified connector for current port. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
CND
CNG
Description
Select GPC-7 connector for current port. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
CNG
CNTR <NRf>
CNTR?
Description
Enter center frequency. Output center frequency.
Cmd Parameters
<NRf>
Query Parameters
NA
Output
<NR3>
Syntax Example
CNTR <NRf>
CNTR?
COF
Description
Turn RF Correction Off. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
COF
CON
CON?
Description
Turn RF Correction On. Output RF Correction On/Off status.
Cmd Parameters
NA
Query Parameters
NA
Output
<NR1> 0|1
Where:
• 0 for Off
• 1 for On
Syntax Example
CON
CON?
COO <NRf>
COO?
Description
Enter offset for open for user specified connector. Output offset for open for user specified connector.
Cmd Parameters
<NRf>
Query Parameters
NA
Output
<NR3>
Syntax Example
COO <NRf>
COO?
COPY <string1>, <string2>
Description
Copy the contents of one file <string1> to another file <string2>. No query.
Cmd Parameters
NA
Output
<string>
Syntax Example
COPY <string1>, <string2>
COS <NRf>
COS?
Description
Enter offset for short for user specified connector. Output offset for short for user specified connector
Cmd Parameters
<NRf>
Query Parameters
NA
Output
<NR3>
Syntax Example
COS <NRf>
COS?
CRB
Description
Select Reflection Both Ports Calibration. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
CRB
CRD
Description
Collect raw data in an internal buffer. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
CRD
CRF
Description
Select Reflection Port One Calibration. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
CRF
CRR
Description
Select Reflection Port Two Calibration. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
CRR
CRT
Description
Select Transmission Frequency Response Reverse Path Calibration. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
CRT
CSB
Description
Clear status bytes and structures (same as *CLS). No query.
Cmd Parameters
NA
Output
NA
Syntax Example
CSB
CSL
Description
Clear the service log. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
CSL
CTN
Description
Continue sweeping from current point. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
CTN
CWD?
Description
Query only. Query the current working directory.
Query Parameters
NA
Output
<ASCII>
Syntax Example
CWD?
CWF <NRf>
CWF?
Description
Enter CW frequency and turn CW on. Output CW frequency.
Cmd Parameters
<NRf>
Query Parameters
NA
Output
<NR3>
Syntax Example
CWF <NRf>
CWF?
CWON
CWON?
Description
Turn CW on at current CW frequency. Output CW on/off status.
Cmd Parameters
NA
Query Parameters
NA
Output
<NR1>
Where:
• 0 for Off
• 1 for On
Syntax Example
CWON
CWON?
CWP <NRf>
CWP?
Description
Enter number of points drawn in CW. Output number of points drawn in CW.
Cmd Parameters
<NRf>
Query Parameters
NA
Output
<NR1>
Syntax Example
CWP <NRf>
CWP?
CXX?
Description
Query only. Output calibration type.
Query Parameters
NA
Output
<NR1> 0|1|2|3|4|5|6|7|8|9
Where the calibration type is:
• 0 for None
• 1 for 12 Term - full path two port
• 2 for 8 Term - 1 path two port FWD
• 3 for 8 Term - 1 path two port REV
• 4 for Transmission FWD
• 5 for Transmission REV
• 6 for Transmission FWD and REV
• 7 for Reflection FWD
• 8 for Reflection REV
• 9 for Reflection FWD and REV
Syntax Example
CXX?
D12
Description
Sets a two trace 1 x 2 layout on the active channel. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
D12
D13
Description
Sets a four trace 2 x 2 layout on the active channel. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
D13
D14
Description
Sets a four trace 2 X 2 layout on the active channel. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
D14
D24
Description
Sets a four trace 2 x 2 layout on the active channel. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
D24
DA1
Description
Select a1 as denominator for parameter being defined. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
DA1
DA2
Description
Select a2 as denominator for parameter being defined. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
DA2
DAT
DAT?
Description
Display measurement data only on active trace. Output data and memory display mode on active trace.
Cmd Parameters
NA
Query Cmd Parameters
NA
Output
<NR1> 1|2|3|4
Where:
• 1 for Data
• 2 for Memory
• 3 for Data & Memory
• 4 for Data With Memory Mathematically Combined
Syntax Example
DAT
DAT?
DATE <NRf> [, <NRf Data>][, <NRf Data>]
DATE?
Description
Enter the date string for tabular data. Output the date string for tabular data.
Cmd Parameters
<NRf>, [NRf Data>], [<NRf Data>]
Query Parameters
NA
Output
<char>
Syntax Example
DATE <NRf>, [NRf Data], [NRf Data]
DATE?
DB1
Description
Select b1 as denominator for parameter being defined. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
DB1
DB2
Description
Select b2 as denominator for parameter being defined. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
DB2
DBP
Description
Select distance bandpass mode for active channel. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
DBP
DCA
Description
Select automatic DC term calculation for low pass. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
DCA
DCCTN
DCCTN?
Description
Resume internal buffer data collection. Output internal buffer data collection resume/suspend status
Cmd Parameters
NA
Output
<NR1>
Syntax Example
DCCTN
DCCTN?
DCHLD
Description
Suspend internal buffer data collection. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
DCHLD
DCMRK
Description
Inserts the mark value into the internal buffer. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
DCMRK
DCO
Description
Select open for DC term calculation for low pass. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
DCO
DCOFF
Description
Turn internal buffer data collection mode off. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
DCOFF
DCPCUR?
Description
Output data collection buffer current point count.
Cmd Parameters
NA
Output
NA
Syntax Example
DCPCUR?
DCPMAX?
Description
Output data collection buffer maximum number of points.
Cmd Parameters
NA
Output
NA
Syntax Example
DCPMAX?
DCS
Description
Select short for DC term calculation for low pass. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
DCS
DCV <NRf>
DCV?
Description
Enter value for DC term calculation for low pass. Output value for DC term calculation for low pass.
Cmd Parameters
NA
Query Cmd Parameters
NA
Output
<NR3>
Syntax Example
DCV <NRf>
DCV?
DCX?
Description
Query only. Output low pass DC term selection.
Cmd Parameters
NA
Output
<NR1>
Syntax Example
DCX?
DCZ
Description
Select line impedance for DC term calculation for low pass. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
DCZ
DD0
Description
Turn data drawing off. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
DD0
DD1
DD1?
Description
Turn data drawing on. Output drawing on/off status.
Cmd Parameters
NA
Query Cmd Parameters
NA
Output
<NR1>
Syntax Example
DD1
DD1?
DDX?
Description
Query only. Output active channel domain parameter frequency distance or time
Cmd Parameters
NA
Output
<NR1> 0|1|2
Where:
• 0 for Frequency
• 1 for Time
• 2 for Distance
Syntax Example
DDX?
DE1
Description
Select Unity as denominator for parameter being defined. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
DE1
DECH <string>
Description
Delete calibration/front panel setup from hard disk or memory card. No query.
Cmd Parameters
<string>
Output
NA
Syntax Example
DECH <string>
DEDH <string>
Description
Delete tabular data file from hard disk or memory card. No query.
Cmd Parameters
<String>
Output
NA
Syntax Example
DEDH <string>
DEFGT?
Description
Output the Instrument Default Gateway address. No query.
Cmd Parameters
<char>
Output
<char>
Syntax Example
DEFGT?
DEL <string>
Description
Delete a file from disk or memory card. No query.
Cmd Parameters
NA
Output
<string>
Syntax Example
DEL <string>
DELCALH <string>
Description
Delete calibration/front panel setup from hard disk or memory card. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
DELCALH <string>
DELDATH <string>
Description
Delete tabular data from hard disk or memory card. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
DELDATH <string>
DELELGH <string>
Description
Delete error list file from hard disk or memory card. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
DELELGH <string>
DELLOGH <string>
Description
Delete service log from hard disk or memory card. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
DELELGH <string>
DELNRMH <string>
Description
Delete trace memory file from hard disk. No query.
Cmd Parameters
<string>
Output
NA
Syntax
DELNRMH <string>
DEN?
Description
Query only. Output denominator selection for parameter being defined
Query Parameters
NA
Output
<NR1> 1|2|3|4|5|
Where:
• 1 for Unity
• 2 for a1
• 3 for a2
• 4 for b1
• 5 for b2
Syntax Example
DEN?
DENH <string>
Description
Delete trace memory file from hard disk. No query.
Parameters
<string>
Output
NA
Syntax
DENH <string>
DFC
Description
Select discrete frequency data points define mode. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
DFC
DFD
Description
Done defining discrete frequencies and range for active channel. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
DFD
DFK
Description
Display K female connector information. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
DFK
DFN
Description
Display N female connector information. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
DFN
DFQ <NRf>
DFQ?
Description
Enter single discrete frequency. Output current discrete frequency.
Cmd Parameters
<NRf>
Query Parameters
NA
Output
<NR3>
Syntax Example
DFQ <NRf>
DFG?
DFV
Description
Display V female connector information. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
DFV
DIA
Description
Select air as active dielectric. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
DIA
DIE <NRf>
Description
Enter a dielectric value. No query.
Cmd Parameters
NA
Output
<NRf>
Syntax Example
DIE <NRf>
DIM
Description
Select microporous teflon as active dielectric. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
DIM
DIP
Description
Select polyethylene as active dielectric. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
DIP
DIR {optional <string>}
Description
Display the contents of a directory. No query.
Cmd Parameters
NA
Output
<arbitrary block>
Syntax Example
DIR {optional <string>}
DIS
DIS?
Description
Display active segmented limit. Output active segmented limit on/off status.
Cmd Parameters
NA
Query Parameters
NA
Output
<NR1> 0|1
Where:
• 0 for Off
• 1 for On
Syntax Example
DIS
DIS?
DISKAP <String>, <Arbitrary Block>
Description
The command appends GPIB data to a disk file. If the directory and file name exist, the command appends the data to the existing file. If they do not exist, they are created. No query.
Cmd Parameters
<String>, <Arbitrary Block>
Where:
• <String> = directory path and file name such as “C:\directory path\filename.extenson”
• <Arbitrary Block> = GPIB data to be appended to the file above.
Select frequency with time gate for active channel. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
FGT
FHI
Description
Set data points to 1601. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
FHI
FIL
Description
Fill defined discrete frequency range. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
FIL
FLO
Description
Set data points to 101. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
FLO
FLTBW?
Description
Query only. Output filter bandwidth.
Query Parameters
NA
Output
<NR3>
Syntax Example
FLTBW?
FLTC?
Description
Query only. Output filter center frequency.
Query Parameters
NA
Output
<NR3>
Syntax Example
FLTC?
FLTL?
Description
Query only. Output filter loss at reference value.
Query Parameters
NA
Output
<NR3>
Syntax Example
FLTL?
FLTQ?
Description
Query only. Output filter Q value.
Query Parameters
NA
Output
<NR3>
Syntax Example
FLTQ?
FLTS?
Description
Query only. Output filter shape factor.
Query Parameters
NA
Output
<NR3>
Syntax Example
FLTS?
FMA
Description
Select ASCII data transfer format. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
FMA
FMB
Description
Select IEEE754 64 bit data transfer format. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
FMB
FMC
Description
Select IEEE754 32 bit data transfer format. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
FMC
FME
Description
Set data points to 401. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
FME
FMT0
Description
Select normal ASCII data element delimiting. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
FMT0
FMT1
Description
Select enhanced ASCII data element delimiting. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
FMT1
FMTX?
Description
Query only. Output ASCII data element delimiting mode.
Query Parameters
NA
Output
<NR1>
Where:
• 0 for normal delimiting
• 1 for enhanced delimiting
Syntax Example
FMTX?
FMX?
Description
Query only. Output data output mode as FMA, FMB, or FMC.
Query Parameters
NA
Output
<NR1> 0|1|2|
Where:
• 0 for FMA
• 1 for FMB
• 2 for FMC
Syntax Example
FMX?
FOF
Description
Blank frequency information. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
FOF
FON
Description
Display frequency information. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
FON
FOX?
Description
Query only. Output frequency information blanking on/off status.
Query Parameters
NA
Output
<NR1> 0|1
Where:
• 0 for Off
• 1 for On
Syntax Example
FOX?
FP0
Description
Turn flat power correction off. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
FP0
FP1
Description
Turn flat power correction on. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
FP1
FPX?
Description
Output flat power correction on/off status. No query.
Query Parameters
NA
Output
<NR1> 0|1
Where:
• 0 for Off
• 1 for On
Syntax Example
FPX?
FQD
Description
Select frequency domain for active channel. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
FQD
FRC
Description
Clear all defined discrete frequencies and range. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
FRC
FRI <NRf>
FRI?
Description
Enter discrete fill range increment frequency. Output discrete fill range increment frequency.
Cmd Parameters
<NRf>
Query Parameters
NA
Output
<NR3>
Syntax Example
FRI <NRf>
FRI?
FRP <NRf>
FRP?
Description
Enter discrete fill range number of points to fill. Output discrete increment count.
Cmd Parameters
<NRf>
Query Parameters
NA
Output
<NR3>
Syntax Example
FRP <NRf>
FRP?
FRS <NRf>
FRS?
Description
Enter discrete fill range start frequency. Output discrete start frequency.
Cmd Parameters
<NRf>
Query Parameters
NA
Output
<NR3>
Syntax Example
FRS <NRf>
FRS?
GCMP <NRf>
GCMP?
Description
Enter gain compression point search value. Output gain compression point search value.
Cmd Parameters
NA
Query Parameters
NA
Output
<NR3>
Syntax Example
GCMP <NRf>
GCMP?
GCT <NRf>
GCT?
Description
Enter gate center value distance or time. Output gate center value distance or time.
Cmd Parameters
<NRf>
Query Parameters
<NR1>
Output
<NR1>
Syntax Example
GCT <NRf>
GCT?
GDS
Description
Display gate symbols on active trace. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
GDS
GLS
Description
Select wide gate shape. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
GLS
GMS
Description
Select maximum gate shape. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
GMS
GNM
Description
Select nominal gate shape. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
GNM
GOF
GOF?
Description
Turn off gating mode for active channel. Output the time domain gating mode on/off display for active channel.
Cmd Parameters
NA
Query Parameters
NA
Output
<NR1>
Where:
• 0 for Off
• 1 for On
• 2 for display gate symbols
Syntax Example
GOF
GOF?
GON
Description
Turn on gating mode for active channel. No query.
Syntax Example
GON
Cmd Parameters
NA
Output
NA
Syntax Example
GON
GRF?
Description
Query only. Output graph type for the active trace display.
Output
<NR1> 0|1|2|3|4|5|6|7|8|9
Where:
• 1 for log mag
• 2 for phase
• 3 for log mag & phase
• 4 for Smith-impedance
• 5 for SWR
• 6 for group delay
• 7 for Smith-admittance
• 8 for linear polar
• 9 for log polar
Syntax Example
GRF?
GRT
Description
Select minimum gate shape. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
GRT
GSN <NRf>
GSN?
Description
Enter gate span value distance or time. Output gate span value distance or time.
Cmd Parameters
<NRf>
Query Parameters
<NR3>
Output
<NR3>
Syntax Example
GSN <NRf>
GSN?
GSP <NRf>
GSP?
Description
Enter gate stop value distance or time. Output gate stop value distance or time.
Cmd Parameters
<NRf>
Query Parameters
NA
Output
<NR3>
Syntax Example
GSP <NRf>
GSP?
GST <NRf>
GST?
Description
Enter gate start value distance or time. Output gate start value distance or time.
Cmd Parameters
<NRf>
Query Parameters
NA
Output
<NR3>
Syntax Example
GST <NRf>
GST?
GSX?
Description
Query only. Output gate shape.
Cmd Parameters
<NR1>
Output
<NR1>
Syntax Example
GSX?
HC0
Description
Disable Automatic IF Calibration. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
HC0
HC1
Description
Enable Automatic IF Calibration. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
HC1
HCT
HCT?
Description
Trigger an IF Calibration. Trigger an IF Calibration and return Pass/Fail result.
Cmd Parameters
NA
Query Parameters
NA
Output
<NR1>
Syntax Example
HCT
HCT?
HCX?
Description
Output Internal Automatic IF Calibration enable/disable status. No query.
Query Parameters
NA
Output
<NR1> 0|1
Where:
• 0 for disabled
• 1 for enabled
Syntax Example
HCX?
HD0
Description
Disable including a heading with data files. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
HD0
HD1
Description
Enable including a heading with data files. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
HD1
HDX?
Description
Query only. Outputs the enable/disable status of including a heading with data files.
Query Parameters
NA
Output
<NR1>
Syntax Example
HDX?
HID
Description
Hide active segmented limit. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
HID
HLD
HLD?
Description
Put sweep into hold mode. Output the sweep hold status.
Cmd Parameters
NA
Query Parameters
NA
Output
<NR1> 0|1
Where:
• 0 for not in hold
• 1 for in hold
Syntax Example
HLD
HLD?
IACCHAR <Arbitrary Block>
Description
Input autocal characterization data from the GPIB. No query.
Cmd Parameters
<Arbitrary Block>
Output
NA
Syntax Example
IACCHAR <Arbitrary Block>
IARF <arbitrary block>, <arbitrary block>
Description
Enter adapter removal files from GPIB and calibrate. No query.
Cmd Parameters
NA
Output
<Arbitrary Block>, <Arbitrary Block>
Syntax Example
IARF <arbitrary block>, <arbitrary block>
IC1 <arbitrary block>
Description
Enter Calibration Coefficient number 1. Inputs a floating point array in <block> format whose size is equal to twice the number of points in the current sweep (real and imaginary data pairs for each point.
Cmd Parameters
<Arbitrary Block>
Output
NA
Syntax Example
IC1 <arbitrary block>
IC10 <arbitrary block>
Description
Enter Calibration Coefficient number 10. Inputs a floating point array in <block> format whose size is equal to twice the number of points in the current sweep (real and imaginary data pairs for each point).
Cmd Parameters
<Arbitrary Block>
Output
NA
Syntax Example
IC10 <arbitrary block>
IC11 <arbitrary block>
Description
Enter Calibration Coefficient number 11. Inputs a floating point array in <block> format whose size is equal to twice the number of points in the current sweep (real and imaginary data pairs for each point).
Cmd Parameters
<Arbitrary Block>
Output
NA
Syntax Example
IC11 <arbitrary block>
IC12 <arbitrary block>
Description
Enter Calibration Coefficient number 12. Inputs a floating point array in <block> format whose size is equal to twice the number of points in the current sweep (real and imaginary data pairs for each point).
Cmd Parameters
<Arbitrary Block>
Output
NA
Syntax Example
IC12 <arbitrary block>
IC2 <arbitrary block>
Description
Enter Calibration Coefficient number 2. Inputs a floating point array in <block> format whose size is equal to twice the number of points in the current sweep (real and imaginary data pairs for each point).
Cmd Parameters
<Arbitrary Block>
Output
NA
Syntax Example
IC2 <arbitrary block>
IC3 <arbitrary block>
Description
Enter Calibration Coefficient number 3. Inputs a floating point array in <block> format whose size is equal to twice the number of points in the current sweep (real and imaginary data pairs for each point).
Cmd Parameters
<Arbitrary Block>
Output
NA
Syntax Example
IC3 <arbitrary block>
IC4 <arbitrary block>
Description
Enter Calibration Coefficient number 4. Inputs a floating point array in <block> format whose size is equal to twice the number of points in the current sweep (real and imaginary data pairs for each point).
Cmd Parameters
<Arbitrary Block>
Output
NA
Syntax Example
IC4 <arbitrary block>
IC5 <arbitrary block>
Description
Enter Calibration Coefficient number 5. Inputs a floating point array in <block> format whose size is equal to twice the number of points in the current sweep (real and imaginary data pairs for each point).
Cmd Parameters
<Arbitrary Block>
Output
NA
Syntax Example
IC5 <arbitrary block>
IC6 <arbitrary block>
Description
Enter Calibration Coefficient number 6. Inputs a floating point array in <block> format whose size is equal to twice the number of points in the current sweep (real and imaginary data pairs for each point).
Cmd Parameters
<Arbitrary Block>
Output
NA
Syntax Example
IC6 <arbitrary block>
IC7 <arbitrary block>
Description
Enter Calibration Coefficient number 7. Inputs a floating point array in <block> format whose size is equal to twice the number of points in the current sweep (real and imaginary data pairs for each point).
Cmd Parameters
<Arbitrary Block>
Output
NA
Syntax Example
IC7 <arbitrary block>
IC8 <arbitrary block>
Description
Enter Calibration Coefficient number 8. Inputs a floating point array in <block> format whose size is equal to twice the number of points in the current sweep (real and imaginary data pairs for each point).
Cmd Parameters
<Arbitrary Block>
Output
NA
Syntax Example
IC8 <arbitrary block>
IC9 <arbitrary block>
Description
Enter Calibration Coefficient number 9. Inputs a floating point array in <block> format whose size is equal to twice the number of points in the current sweep (real and imaginary data pairs for each point).
Cmd Parameters
<Arbitrary Block>
Output
NA
Syntax Example
IC9 <arbitrary block>
ICA <arbitrary block>
Description
Enter Calibration Coefficient number 10. Inputs a floating point array in <block> format whose size is equal to twice the number of points in the current sweep (real and imaginary data pairs for each point).
Cmd Parameters
<Arbitrary Block>
Output
NA
Syntax Example
ICA <arbitrary block>
ICB <arbitrary block>
Description
Enter Calibration Coefficient number 11. Inputs a floating point array in <block> format whose size is equal to twice the number of points in the current sweep (real and imaginary data pairs for each point).
Cmd Parameters
<Arbitrary Block>
Output
NA
Syntax Example
ICB <arbitrary block>
ICC <arbitrary block>
Description
Enter Calibration Coefficient number 12. Inputs a floating point array in <block> format whose size is equal to twice the number of points in the current sweep (real and imaginary data pairs for each point).
Cmd Parameters
<Arbitrary Block>
Output
NA
Syntax Example
ICC <arbitrary block>
ICD <arbitrary block>
Description
Input corrected S-Parameter data to display on the active trace. No query.
Cmd Parameters
<Arbitrary Block>
Output
NA
Syntax Example
ICD <arbitrary block>
ICF <arbitrary block>
Description
Input Front Panel and Calibration Data. No query.
Cmd Parameters
<Arbitrary Block>
Output
NA
Syntax Example
ICF <arbitrary block>
ICL <arbitrary block>
Description
Enter All Applicable Calibration Coefficients. No query.
Cmd Parameters
<Arbitrary Block>
Output
NA>
Syntax Example
ICL <arbitrary block>
IEDEF <arbitrary block>, <arbitrary block>
Description
Enter embedding/de-embedding data from GPIB and embed/de-embed. Enter the data as two <block> format data blocks. The first contains the Front Panel and Cal Data. The second contains the S2P data.
Cmd Parameters
<Arbitrary Block>, <Arbitrary Block>
Output
NA
Syntax Example
IEDEF <arbitrary block>, <arbitrary block>
IEM <NRf>
Description
Enter extended status event mask value. No query.
Cmd Parameters
NA
Output
<NRf>
Syntax Example
IEM <NRf>
IF1
Description
Set 10 Hz IF Bandwidth. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
IF1
IF2
Description
Set 100 Hz IF Bandwidth. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
IF2
IF3
Description
Set 1000 Hz IF Bandwidth. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
IF3
IF4
Description
Set 10000 Hz IF Bandwidth. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
IF4
IFA
Description
Set 10000 Hz IF Bandwidth. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
IFA
IFD <arbitrary block>
Description
Enter Formatted data. No query. Inputs a floating point array in <block> format whose size is equal to the number of points in the current sweep (the array size is doubled for dual graph displays, i.e. log mag/phase). The IFD command inputs an <block> containing either ASCII or binary formatted data depending on the currently selected format.
Cmd Parameters
<Arbitrary Block>
Output
NA
Syntax Example
IFD <arbitrary block>
IFM
Description
Set 10 Hz IF Bandwidth. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
IFM
IFN
Description
Set 1000 Hz IF Bandwidth. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
IFN
IFP <arbitrary block>
Description
Enter current front panel setup. No query.
Cmd Parameters
<Arbitrary Block>
Output
NA
Syntax Example
IFP <arbitrary block>
IFPC <arbitrary block>
Description
Input flat power coefficients. No query.
Cmd Parameters
<Arbitrary Block>
Output
NA
Syntax Example
IFPC <arbitrary block>
IFR
Description
Set 100 Hz IF Bandwidth. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
IFR
IFV <arbitrary block>
Description
Enter frequency values. No query.
Cmd Parameters
<Arbitrary Block>
Output
NA
Syntax Example
IFV <arbitrary block>
IFX?
Description
Query only. Output the IF bandwidth.
Query Parameters
NA
Output
<NR3> 1|2|3|4
Where:
• 1 for 10 Hz
• 2 for 100 Hz
• 3 for 1 kHz
• 4 for 10 kHz
Syntax Example
IFX?
IKIT <Arbitrary Block>
Description
Enter calibration kit data from GPIB. No query.
Cmd Parameters
<Arbitrary Block>
Output
NA
Syntax Example
IKIT <Arbitrary Block>
ILM <NRf>
Description
Enter limits status byte mask. No query.
Cmd Parameters
<NRf>
Output
NA
Syntax Example
ILM <NRf>
IMCF <arbitrary block>, <arbitrary block>
Description
Enter merge calibrations files from GPIB and combine. No query.
Cmd Parameters
<Arbitrary Block>, <Arbitrary Block>
Output
NA
Syntax Example
IMCF <arbitrary block>, <arbitrary block>
IMG
Description
Select Imaginary display for the active trace. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
IMG
IND <arbitrary block>
Description
Enter trace memory for the active trace. No query.
Enter NXN data and send device 1 data to GPIB. Enter the data as three format data blocks. The first contains the S2P data for the device1-2 combination. The second contains the S2P data for the device 1-3 combination. The third contains the S2P data for the device 2-3 combination. The S2P data for device 1 is output in <block> format. No query.
Enter NXN data and send device 2 data to GPIB. Enter the data as three format data blocks. The first contains the S2P data for the device 1-2 combination. The second contains the S2P data for the device 1-3 combination. The third contains the S2P data for the device 2-3 combination. The S2P data for device 2 is output in <block> format. No query.
Enter NXN data and send device 3 data to GPIB. Enter the data as three format data blocks. The first contains the S2P data for the device 1-2 combination. The second contains the S2P data for the device 1-3 combination. The third contains the S2P data for the device 2-3 combination. The S2P data for device 3 is output in <block> format. No query.
Enter NXN data and save device 1 data to disk. Enter the data as a filename in data format followed by three data blocks in format. The file receives the device 1 S2P data. The first block contains the device 1-2 S2P data. The second block contains the device 1-3 S2P data. The third block contains the device 2-3 S2P data. The file resides on the VNA Hard drive or other memory device. No query.
Enter NXN data and save device 2 data to disk. Enter the data as a filename in data format followed by three data blocks in format. The file receives the device 2 S2P data. The first block contains the device 1-2 S2P data. The second block contains the device 1-3 S2P data. The third block contains the device 2-3 S2P data. The file resides on the VNA Hard drive or other memory device. No query.
Enter NXN data and save device 3 data to disk. Enter the data as a filename in data format followed by three data blocks in format. The file receives the device 3 S2P data. The first block contains the device 1-2 S2P data. The second block contains the device 1-3 S2P data. The third block contains the device 2-3 S2P data. The file resides on the VNA Hard drive or other memory device.
Load adapter removal files from disk and calibrate. No query.
Cmd Parameters
<String>, <String>
Output
NA
Syntax Example
LDARF <string>, <string>
LDEDEF <string>, <string>
Description
Load embedding/de-embedding files from disk and embed/de-embed. Enter the data as two file names in <string> data format.The first file contains the Front Panel and Cal Data. The second file contains the S2P data. These files must reside on the VNA Hard drive or memory device. No query.
Cmd Parameters
<String>, <String>
Output
NA
Syntax Example
LDEDEF <string>, <string>
LDMCF <string>, <string>
Description
Load merge calibrations files from disk and combine. Enter the calibration file name in <string> data format specifying the path and filename of the calibration file to load. No query.
Cmd Parameters
<String>, <String>
Output
NA
Syntax Example
LDMCF <string>, <string>
LDNXNIFO1 <string>, <string>, <string>, <string>
Description
Load NXN and IF data from disk and send device 1 data to GPIB. Enter the data as four file names in <string> data format where:
• The first file contains the device 1-2 S2P data.
• The second file contains the device 1-3 S2P data.
• The third file contains the device 2-3 S2P data.
• The fourth file contains the IF PATH S2P File.
The device 1 S2P data is output in <block> format. No query.
Cmd Parameters
<String>, <String>, <String>, <String>
Output
<Arbitrary Block>
Syntax Example
LDNXNIFO1 <string>, <string>, <string>, <string>
LDNXNIFO2 <string>, <string>, <string>, <string>
Description
Load NXN and IF data from disk and send device 2 data to GPIB. Enter the data as four file names in <string> data format where:
• The first file contains the device 1-2 S2P data.
• The second file contains the device 1-3 S2P data.
• The third file contains the device 2-3 S2P data.
• The fourth file contains the IF PATH S2P File.
The device 2 S2P data is output in <block> format. No query.
Cmd Parameters
<String>, <String>, <String>, <String>
Output
<Arbitrary Block>
Syntax Example
LDNXNIFO2 <string>, <string>, <string>, <string>
LDNXNIFO3 <string>, <string>, <string>, <string>
Description
Load NXN and IF data from disk and send device 3 data to GPIB. Enter the data as four file names in <string> data format, where:
• The first file contains the device 1-2 S2P data.
• The second file contains the device 1-3 S2P data.
• The third file contains the device 2-3 S2P data.
• The fourth file contains the IF PATH S2P File.
The device 3 S2P data is output in <block> format. No query.
Query only. Output trace math type for active trace
Query Parameters
NA
Output
<NR1> 0|1|2|3|4
Where:
• 1 for add
• 2 for subtract
• 3 for multiply
• 4 for divide
Syntax Example
MTH?
MUL
Description
Select multiplication as trace math for active trace. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
MUL
NA1
Description
Select a1 as numerator for parameter being defined. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
NA1
NA2
Description
Select a2 as numerator for parameter being defined. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
NA2
NB1
Description
Select b1 as numerator for parameter being defined. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
NB1
NB2
Description
Select b2 as numerator for parameter being defined. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
NB2
NCS
Description
Setup the next calibration step. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
NCS
NMKR
Description
Select normal markers on all channels marker display mode. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
NMKR
NOC
Description
Select normal points sweep. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
NOC
NOFST <NRf>
NOFST?
Description
Enter nominal offset value for external gain. Enter nominal offset value for external gain.
Cmd Parameters
<NRf>
Query Parameters
NA
Output
<NR3>
Syntax Example
NOFST <NRf>
NOFST?
NP <NRf>
Description
Set number of sweep data points. No query.
Cmd Parameters
NA
Output
<NRf>
Syntax Example
NP <NRf>
NP101
Description
Set data points to 101. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
NP101
NP1601
Description
Set data points to 1601. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
NP1601
NP201
Description
Set data points to 201. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
NP201
NP401
Description
Set data points to 401. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
NP401
NP51
Description
Set data points to 51. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
NP51
NP801
Description
Set data points to 801. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
NP801
NRMS
Description
Normalize S21 for gain compression testing. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
NRMS
NRMS21
Description
Select gain compression bottom graph displays Normalized S21. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
NRMS21
NU1
Description
Select Unity as numerator for parameter being defined. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
NU1
NUM?
Description
Query only. Output numerator selection for parameter being defined.
Query Parameters
NA
Output
<NR1> 1|2|3|4|5
Where:
• 1 for unity
• 2 for a1
• 3 for a2
• 4 for b1
• 5 for b2
Syntax Example
NUM?
NXNIFFWD
NXNIFFWD?
Description
Sets the NXN IF sweep direction flag to forward. Outputs the NXN IF sweep direction flag forward/reverse status.
Cmd Parameters
NA
Query Parameters
NA
Output
<NR1>
Syntax Example
NXNIFFWD
NXNIFFWD?
NXNIFREV
Description
Sets the NXN IF sweep direction flag to reverse
Cmd Parameters
NA
Output
NA
Syntax Example
NXNIFREV
NXNL1 <NRf>
NXNL1?
Description
Enter length for NXN device 1. Output length for NXN device 1.
Cmd Parameters
<NRf>
Query Parameters
NA
Output
<NR3>
Syntax Example
NXNL1 <NRf>
NXNL1?
NXNL2 <NRf>
NXNL2?
Description
Enter length for NXN device 2. Output length for NXN device 2.
Cmd Parameters
<NRf>
Query Parameters
NA
Output
<NR3>
Syntax Example
NXNL2 <NRf>
NXNL2?
NXNL3 <NRf>
NXNL3?
Description
Enter length for NXN device 3. Output length for NXN device 3.
Cmd Parameters
<NRf>
Query Parameters
NA
Output
<NR3>
Syntax Example
NXNL3 <NRf>
NXNL3?
O3CM
Description
Select Triple Offset Short (SSST) calibration method. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
O3CM
O4FD
Description
Output formatted data of the first four traces. No query.
Cmd Parameters
NA
Output
<Arbitrary Block>
Syntax Example
O4FD
O4SC
Description
Output all 4 Corrected S-Cmd Parameters. No query.
Cmd Parameters
NA
Output
<Arbitrary Block>
Syntax Example
O4SC
O4SR
Description
Output all 4 Raw S-Cmd Parameters. No query.
Cmd Parameters
NA
Output
<Arbitrary Block>
Syntax Example
O4SR
OACCHAR
Description
Output AutoCal characterization data to the GPIB. No query.
Cmd Parameters
NA
Output
<Arbitrary Block>
Syntax Example
OACCHAR
OACSER
Description
Get AutoCal box serial number. No query.
Cmd Parameters
NA
Output
<Char>
Syntax Example
OACSER
OACTYPE
Description
Get AutoCal box type. No query.
Cmd Parameters
NA
Output
<Char>
Syntax Example
OACTYPE
OAM1
Description
Output channel 1 active marker value. No query.
The word “channel” in this Lightning command definition refers to a “trace” in the VectorStar VNA. The use of this command requires that the VectorStar VNA be configured with one (1) channel and four (4) traces. If the VectorStar VNA is configured with one channel and more than four traces, traces five and higher cannot be accessed by this command. If the VectorStar VNA is running in a multi-channel configuration, it is recommended to not use this command.
If Trace 1 does not exist, the command generates an error.
Cmd Parameters
NA
Output
<NR3>
Syntax Example
OAM1
OAM2
Description
Output channel 2 active marker value. No query.
The word “channel” in this Lightning command definition refers to a “trace” in the VectorStar VNA. The use of this command requires that the VectorStar VNA be configured with one (1) channel and four (4) traces. If the VectorStar VNA is configured with one channel and more than four traces, traces five and higher cannot be accessed by this command. If the VectorStar VNA is running in a multi-channel configuration, it is recommended to not use this command.
If Trace 2 does not exist, the command generates an error.
Cmd Parameters
NA
Output
<NR3>
Syntax Example
OAM2
OAM3
Description
Output channel 3 active marker value. No query.
The word “channel” in this Lightning command definition refers to a “trace” in the VectorStar VNA. The use of this command requires that the VectorStar VNA be configured with one (1) channel and four (4) traces. If the VectorStar VNA is configured with one channel and more than four traces, traces five and higher cannot be accessed by this command. If the VectorStar VNA is running in a multi-channel configuration, it is recommended to not use this command.
If Trace 3 does not exist, the command generates an error.
Cmd Parameters
NA
Output
<NR3>
Syntax Example
OAM3
OAM4
Description
Output channel 4 active marker value. No query.
The word “channel” in this Lightning command definition refers to a “trace” in the VectorStar VNA. The use of this command requires that the VectorStar VNA be configured with one (1) channel and four (4) traces. If the VectorStar VNA is configured with one channel and more than four traces, traces five and higher cannot be accessed by this command. If the VectorStar VNA is running in a multi-channel configuration, it is recommended to not use this command.
If Trace 4 does not exist, the command generates an error.
Cmd Parameters
NA
Output
<NR3>
Syntax Example
OAM4
OBMB
Description
Output the display as a black and white bitmap (obsolete). No query.
Cmd Parameters
NA
Output
<Char>
Syntax
OBMB
OBMC
Description
Output the display as a color bitmap (obsolete). No query.
Cmd Parameters
NA
Output
<Char1>
Syntax
OBMC
OBMP
Description
Output the display in Bitmap format. No query.
Cmd Parameters
NA
Output
<Arbitrary Block>
Syntax Example
OBMP
OBMPA
Description
Output the active channel display in Bitmap format. No query.
Cmd Parameters
NA
Output
<Arbitrary Block>
Syntax Example
OBMPA
OC1
Description
Output Correction coefficient number 1. No query.
Cmd Parameters
NA
Output
<Arbitrary Block>
Syntax Example
OC1
OC10
Description
Output Correction coefficient number 10. No query.
Cmd Parameters
NA
Output
<Arbitrary Block>
Syntax Example
OC10
OC11
Description
Output Correction coefficient number 11. No query.
Cmd Parameters
NA
Output
<Arbitrary Block>
Syntax Example
OC11
OC12
Description
Output Correction coefficient number 12. No query.
Cmd Parameters
NA
Output
<Arbitrary Block>
Syntax Example
OC12
OC2
Description
Output Correction coefficient number 2. No query.
Cmd Parameters
NA
Output
<Arbitrary Block>
Syntax Example
OC2
OC3
Description
Output Correction coefficient number 3. No query.
Cmd Parameters
<block>
Output
<arbitrary block>
Syntax Example
OC3
OC4
Description
Output Correction coefficient number 4. No query.
Cmd Parameters
<block>
Output
<arbitrary block>
Syntax Example
OC4
OC5
Description
Output Correction coefficient number 5. No query.
Cmd Parameters
<block>
Output
<arbitrary block>
Syntax Example
OC5
OC6
Description
Output Correction coefficient number 6. No query.
Cmd Parameters
<block>
Output
<arbitrary block>
Syntax Example
OC6
OC7
Description
Output Correction coefficient number 7. No query.
Cmd Parameters
<block>
Output
<arbitrary block>
Syntax Example
OC7
OC8
Description
Output Correction coefficient number 8. No query.
Cmd Parameters
<block>
Output
<arbitrary block>
Syntax Example
OC8
OC9
Description
Output Correction coefficient number 9. No query.
Cmd Parameters
<block>
Output
<arbitrary block>
Syntax Example
OC9
OCA
Description
Output Correction coefficient number 10. No query.
Cmd Parameters
<block>
Output
<arbitrary block>
Syntax Example
OCA
OCB
Description
Output Correction coefficient number 11. No query.
Cmd Parameters
<block>
Output
<arbitrary block>
Syntax Example
OCB
OCC
Description
Output Correction coefficient number 12. No query.
Cmd Parameters
<block>
Output
<arbitrary block>
Syntax Example
OCC
OCD
Description
Output Corrected S-Parameter data on active trace. No query.
Cmd Parameters
<block>
Output
<arbitrary block>
Syntax Example
OCD
OCF
Description
Output Front Panel and Calibration data. No query.
Cmd Parameters
<block>
Output
<arbitrary block>
Syntax Example
OCF
OCL
Description
Output all applicable calibration coefficients for cal type. No query.
Cmd Parameters
<block>
Output
<arbitrary block>
Syntax Example
OCL
OCM
Description
Select Offset Short (SSLT) calibration method. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
OCM
OCS
Description
Select IEEE 754 32 bit data transfer format.
Cmd Parameters
NA
Output
<char1>
Syntax Example
OCS
OCSV
Description
Output the CSV file data. No query.
Cmd Parameters
<block>
Output
<arbitrary block>
Syntax Example
OCSV
ODAT
Description
Output the Tabular file data. No query.
Cmd Parameters
<block>
Output
<arbitrary block>
Syntax Example
ODAT
ODR
Description
Display the contents of the current directory. No query.
Cmd Parameters
<block>
Output
<arbitrary block>
Syntax Example
ODR
ODRH
Description
Display the contents of the current directory. No query.
Cmd Parameters
<block>
Output
<arbitrary block>
Syntax Example
ODRH
ODRIVES
Description
Output list of Logical drives. No query.
Cmd Parameters
<block>
Output
<arbitrary block>
Syntax Example
ODRIVES
ODV
Description
Output list of distance values. No query.
Cmd Parameters
<block>
Output
<arbitrary block>
Syntax Example
ODV
OEB
Description
Output extended status event value. No query.
Cmd Parameters
<NR1>
Output
NA
Syntax Example
OEB
OED1
Description
Output port 1 directivity correction coefficient. No query.
Cmd Parameters
<block>
Output
<arbitrary block>
Syntax Example
OED1
OED2
Description
Output port 2 directivity correction coefficient. No query.
Cmd Parameters
<block>
Output
<arbitrary block>
Syntax Example
OED2
OEL
Description
Output the event log. No query.
Cmd Parameters
<block>
Output
<arbitrary block>
Syntax Example
OEL
OEM
Description
Output extended status event mask value. No query.
Cmd Parameters
<NR1>
Output
NA
Syntax Example
OEM
OEP1L
Description
Output load match at port 1 correction coefficient. No query.
Cmd Parameters
<block>
Output
<arbitrary block>
Syntax Example
OEP1L
OEP1S
Description
Output port 1 source match correction coefficient. No query.
Cmd Parameters
<block>
Output
<arbitrary block>
Syntax Example
OEP1S
OEP2L
Description
Output load match at port 2 correction coefficient. No query.
Cmd Parameters
<block>
Output
<arbitrary block>
Syntax Example
OEP2L
OEP2S
Description
Output port 2 source match correction coefficient. No query.
Cmd Parameters
<block>
Output
<arbitrary block>
Syntax Example
OEP2S
OEQ
Description
Output the error queue. No query.
Cmd Parameters
<block>
Output
<arbitrary block>
Syntax Example
OEQ
OEQM
Description
Removes and outputs the oldest error in the error queue. No query.
Cmd Parameters
NA
Output
<ASCII>
Syntax Example
OEQM
OET11
Description
Output port 1 reflection tracking correction coefficient. No query.
Cmd Parameters
<block>
Output
<block>
Syntax Example
OET11
OET12
Description
Output transmission tracking ports 2 to 1 correction coefficient. No query.
Cmd Parameters
<block>
Output
<block>
Syntax Example
OET12
OET21
Description
Output transmission tracking ports 1 to 2 correction coefficient. No query.
Cmd Parameters
<block>
Output
<block>
Syntax Example
OET21
OET22
Description
Output port 2 reflection tracking correction coefficient. No query.
Cmd Parameters
<block>
Output
<block>
Syntax Example
OET22
OEX12
Description
Output leakage ports 2 to 1 correction coefficient. No query.
Cmd Parameters
<block>
Output
<block>
Syntax Example
OEX12
OEX21
Description
Output leakage ports 1 to 2 correction coefficient. No query.
Cmd Parameters
<block>
Output
<block>
Syntax Example
OEX21
OFD
Description
Output formatted data of active trace. No query.
Cmd Parameters
<block>
Output
<block>
Syntax Example
OFD
OFD1
Description
Output formatted data of trace one. No query.
Cmd Parameters
<block>
Output
<block>
Syntax Example
OFD1
OFD2
Description
Output formatted data of trace two. No query.
Cmd Parameters
<block>
Output
<block>
Syntax Example
OFD2
OFD3
Description
Output formatted data of trace three. No query.
Cmd Parameters
<block>
Output
<block>
Syntax Example
OFD3
OFD4
Description
Output formatted data of trace four. No query.
Cmd Parameters
<block>
Output
<block>
Syntax Example
OFD4
OFF <NRf>
OFF?
Description
Enter offset value for top graph of active trace. Output offset value for top graph of active trace.
Cmd Parameters
<NRf>
Query Parameters
NA
Output
<NR3>
Syntax Example
OFF <NRf>
OFF?
OFF2 <NRf>
OFF2?
Description
Enter offset value for bottom graph of active trace. Output offset value for bottom graph of active trace.
Cmd Parameters
<NRf>
Query Parameters
NA
Output
<NR3>
Syntax Example
OFF2 <NRf>
OFF2?
OFP
Description
Output current front panel setup. No query.
Cmd Parameters
<block>
Output
<block>
Syntax Example
OFP
OFPC
Description
Output flat power coefficients. No query.
Cmd Parameters
<block>
Output
<block>
Syntax Example
OFPC
OFV
Description
Output frequency values. No query.
Cmd Parameters
<block>
Output
<block>
Syntax Example
OFV
OGCCSV
Description
Output gain compression results in csv format. No query.
Cmd Parameters
NA
Output
<block>
Syntax Example
OGCCSV
OGCFD
Description
Output gain compression final data to GPIB. No query.
Cmd Parameters
NA
Output
<block>
Syntax Example
OGCFD
OGCFV
Description
Output gain compression frequency values to GPIB. No query.
Cmd Parameters
NA
Output
<block>
Syntax Example
OGCFV
OGCTXT
Description
Output gain compression results in txt format. No query.
Cmd Parameters
NA
Output
<block>
Syntax Example
OGCTXT
OGE
Description
Output extended description of current GPIB error. No query.
Cmd Parameters
NA
Output
<ASCII>
Syntax Example
OGE
OGL
Description
Output extended description of previous GPIB error. No query.
Cmd Parameters
NA
Output
<ASCII>
Syntax Example
OGL
OHDR
Description
Output the Tabular file header data. No query.
Cmd Parameters
<block>
Output
<block>
Syntax Example
OHDR
OI
Description
Output Instrument identification string with serial number. No query.
Cmd Parameters
NA
Output
<ASCII>
Syntax Example
OI
OID
Description
Output Instrument identification string. No query.
Cmd Parameters
NA
Output
<ASCII>
Syntax Example
OID
OJPG
Description
Output the display in JPG format. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
OJPG
OJPGA
Description
Output the active channel display in JPG format. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
OJPGA
OLB
Description
Output limits status byte. No query.
Cmd Parameters
<NR1>
Output
NA
Syntax Example
OLB
OLM
Description
Output limits status byte mask. No query.
Cmd Parameters
<NR1>
Output
NA
Syntax Example
OLM
OM1 <NR3>|<NR3>, <NR3>
Description
The command outputs the marker 1 value or values on the active trace. The number of outputs produced by the query depends on the display type. For example, Log Magnitude displays have one marker value (as a single <NR3> and dual Linear Magnitude and Phase displays have two marker values (as <NR3>, <NR3>). The units of the <NR3> parameters depend on the display type. No query.
Cmd Parameters
<NR3>|<NR3>, <NR3>
Output
NA
Syntax Example
OM1
OM1
Description
The command outputs the marker 1 value or values on the active trace. The number of outputs produced by the query depends on the display type. For example, Log Magnitude displays have one marker value (as a single <NR3> and dual Linear Magnitude and Phase displays have two marker values (as <NR3>, <NR3>). The units of the <NR3> parameters depend on the display type. No query.
Cmd Parameters
NA
Output
<NR3>|<NR3>, <NR3>
Syntax Example
OM1
OM2 <NR3>|<NR3>, <NR3>
Description
Output marker 2 value on active trace. No query.
Cmd Parameters
<NR3>|<NR3>, <NR3>
Output
NA
Syntax Example
OM2
OM3 <NR3>|<NR3>, <NR3>
Description
Output marker 3 value on active trace. No query.
Cmd Parameters
<NR3>|<NR3>, <NR3>
Output
NA
Syntax Example
OM3
OM4 <NR3>|<NR3>, <NR3>
Description
Output marker 4 value on active trace. No query.
Cmd Parameters
<NR3>|<NR3>, <NR3>
Output
NA
Syntax Example
OM4
OM5 <NR3>|<NR3>, <NR3>
Description
Output marker 5 value on active trace. No query.
Cmd Parameters
<NR3>|<NR3>, <NR3>
Output
NA
Syntax Example
OM5
OM6 <NR3>|<NR3>, <NR3>
Description
Output marker 6 value on active trace. No query.
Cmd Parameters
<NR3>|<NR3>, <NR3>
Output
NA
Syntax Example
OM6
OMOD
Description
Output Instrument Model number. No query.
Cmd Parameters
<char>
Output
<char>
Syntax Example
OMOD
ONB
Description
Output number of bands. No query.
Cmd Parameters
<NR1>
Output
NA
Syntax Example
ONB
ONCP
Description
Output number of points for current calibration. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
ONCP
ONCT
Description
Output number of cal terms for current calibration. No query.
Cmd Parameters
<NR1>
Output
NA
Syntax Example
ONCT
OND
Description
Output the active trace memory data. No query.
Cmd Parameters
<block>
Output
<block>
Syntax Example
OND
ONDF
Description
Output the current number of discrete frequency points. No query.
Cmd Parameters
NA
Output
<NR1>
Syntax Example
ONDF
ONE
Description
Output the number of entries in the service log. No query.
Cmd Parameters
<NR1>
Output
NA
Syntax Example
ONE
ONEL
Description
Output the number of entries in the event log. No query.
Cmd Parameters
<NR1>
Output
NA
Syntax Example
ONEL
ONEQ
Description
Output the number of errors in the error queue. No query.
Cmd Parameters
<NR1>
Output
NA
Syntax Example
ONEQ
ONP
Description
Output number of points currently being measured. No query.
Cmd Parameters
<NR1>
Output
NA
Syntax Example
ONP
ONPV
Description
Output the number of power sweep power values. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
ONPV
ONRM
Description
Output stored normalization data to GPIB. No query.
Cmd Parameters
NA
Output
<Arbitrary Block>
Syntax
ONRM
OPB
Description
Output the 488.2 Status Byte value. Same function as *STB?. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
OPB
OPM
Description
Output the status byte mask. No query.
Cmd Parameters
NA
Output
<NR1>
Syntax Example
OPM
OPNG
Description
Output the display in PNG format. No query.
Cmd Parameters
NA
Output
<Arbitrary Block>
Syntax Example
OPNG
OPNGA
Description
Output the active channel display in PNG format. No query.
Cmd Parameters
<block>
Output
<block>
Syntax Example
OPNGA
OPSC
Description
Output power sweep linearity calibration coefficients. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
OPSC
OPSV
Description
Output power sweep values. No query.
Cmd Parameters
NA
Output
<block>
Syntax Example
OPSV
ORD
Description
Output Raw S-Parameter data on active trace. No query.
Cmd Parameters
<block>
Output
<block>
Syntax Example
ORD
OS1
Description
Output front panel setup data from memory location 1. No query.
Cmd Parameters
<block>
Output
<block>
Syntax Example
OS1
OS10
Description
Output front panel setup data from memory location 10. No query.
Cmd Parameters
<block>
Output
<block>
Syntax Example
OS10
OS11C
Description
Output Corrected S-Parameter S11. No query.
Cmd Parameters
<block>
Output
<block>
Syntax Example
OS11C
OS11R
Description
Output Raw S-Parameter S11. No query.
Cmd Parameters
<block>
Output
<block>
Syntax Example
OS11R
OS12C
Description
Output Corrected S-Parameter S12. No query.
Cmd Parameters
<block>
Output
<block>
Syntax Example
OS12C
OS12R
Description
Output Raw S-Parameter S12. No query.
Cmd Parameters
<block>
Output
<block>
Syntax Example
OS12R
OS2
Description
Output front panel setup data from memory location 2. No query.
Cmd Parameters
<block>
Output
<block>
Syntax Example
OS2
OS21C
Description
Output Corrected S-Parameter S21. No query.
Cmd Parameters
<block>
Output
<block>
Syntax Example
OS21C
OS21R
Description
Output Raw S-Parameter S21. No query.
Cmd Parameters
<block>
Output
<block>
Syntax Example
OS21R
OS22C
Description
Output Corrected S-Parameter S22. No query.
Cmd Parameters
<block>
Output
<block>
Syntax Example
OS22C
OS22R
Description
Output Raw S-Parameter S22. No query.
Cmd Parameters
<block>
Output
<block>
Syntax Example
OS22R
OS2P
Description
Output the S2P file data. No query.
Cmd Parameters
<block>
Output
<block>
Syntax Example
OS2P
OS3
Description
Output front panel setup data from memory location 3. No query.
Cmd Parameters
<block>
Output
<block>
Syntax Example
OS3
OS4
Description
Output front panel setup data from memory location 4. No query.
Cmd Parameters
<block>
Output
<block>
Syntax Example
OS4
OS5
Description
Output front panel setup data from memory location 5. No query.
Cmd Parameters
<block>
Output
<block>
Syntax Example
OS5
OS6
Description
Output front panel setup data from memory location 6. No query.
Cmd Parameters
<block>
Output
<block>
Syntax Example
OS6
OS7
Description
Output front panel setup data from memory location 7. No query.
Cmd Parameters
<block>
Output
<block>
Syntax Example
OS7
OS8
Description
Output front panel setup data from memory location 8. No query.
Cmd Parameters
<block>
Output
<block>
Syntax Example
OS8
OS9
Description
Output front panel setup data from memory location 9. No query.
Cmd Parameters
<block>
Output
<block>
Syntax Example
OS9
OSER
Description
Output Instrument serial number. No query.
Cmd Parameters
<char>
Output
<char>
Syntax Example
OSER
OSL
Description
Output the service log. No query.
Cmd Parameters
<block>
Output
<block>
Syntax Example
OSL
OTV
Description
Output list of time values. No query.
Cmd Parameters
<block>
Output
<block>
Syntax Example
OTV
OTXT
Description
Output the TXT file data. No query.
Cmd Parameters
<block>
Output
<block>
Syntax Example
OTXT
P1C
P1C?
Description
Select port 1 for connector specification. Output port 1 connector type.
Cmd Parameters
NA
Query Parameters
NA
Output
<NR1>
Syntax Example
P1C
P1C?
P1P?
Description
Output approximate power level at port 1
Cmd Parameters
<NR3>
Output
<NR3>
Syntax Example
P1P?
P2C
P2C?
Description
Select port 2 for connector specification. Output port 2 connector type.
Cmd Parameters
NA
Query Parameters
NA
Syntax Example
P2C
P2C?
PA1 <NRf>
Description
Set reference attenuator value for power sweep on port 1. No query.
Cmd Parameters
<NRf>
Query Parameters
NA
Syntax
PA1 <NRf>
PCP
Description
Select measurement phase polar chart mode. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
PCP
PCS
Description
Select sweep position polar chart mode. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
PCS
PCX?
Description
Output polar chart mode. No query.
Cmd Parameters
NA
Output
<NR1>
Syntax Example
PCX?
PDRH {<String>}
Description
Print directory listing of the hard drive. No query.
Cmd Parameters
<String> is optional.
Output
NA
Syntax Example
PDRH {<String>}
PDT0
Description
Proprietary internal command. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
PDT0
PDT1
Description
Proprietary internal command. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
PDT1
PEL
Description
Print the error list. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
PEL
PFSC
Description
Configure for printing full screen graphic image.
Parameters
NA
Output
NA
Syntax Example
PFSC
PGR
Description
Print data area graphic image.
Parameters
NA
Output
NA
Syntax Example
PGR
PGRC
Description
Configure for printing data area graphic image.
Parameters
NA
Output
NA
Syntax Example
PGRC
PHA
Description
Select Phase display for the active trace. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
PHA
PHO <NRf>
PHO?
Description
Enter phase shift for display channel. Output phase shift for display channel.
Cmd Parameters
<NRf>
Query Parameters
NA
Output
<NR3>
Syntax Example
PHO <NRf>
PHO?
PLG
Description
Select Log Polar display for the active trace. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
PLG
PLR
Description
Select Linear Polar display for the active trace. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
PLR
PMK
Description
Print tabular data for markers.
Parameters
NA
Output
NA
Syntax Example
PMK
PMKC
Description
Configure for printing tabular data for markers. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
PMKC
PMT
Description
Print tabular data for traces and markers.
Parameters
NA
Output
NA
Syntax Example
PMT
PMTC
Description
Configure for printing tabular data for markers and traces. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
PMTC
POSET <NRf>
POSET?
Description
Enter constant offset phase for active channel. Output constant offset phase for active channel
Cmd Parameters
<NRf>
Query Parameters
NA
Output
<NR3>
Syntax Example
POSET <NRf>
POSET?
POW
Description
Select Power Out display for the active trace
Cmd Parameters
NA
Output
NA
Syntax Example
POW
PSCNFRQ?
Description
Query only. Output the power sweep linearity cal number of frequency points.
Query Parameters
NA
Output
<NR1>
Syntax Example
PSCNFRQ?
PSCNPWR?
Description
Query only. Output the power sweep linearity cal power levels.
Cmd Parameters
NA
Output
NA
Syntax Example
PSCNPWR?
PSCSTEP?
Description
Query only. Output the power sweep linearity cal number of power points.
Cmd Parameters
<NR3 Data>
Output
<NR3 Data>
Syntax Example
PSCSTEP?
PSL
Description
Print the service log.
Cmd Parameters
NA
Output
NA
Syntax Example
PSL
PSP <NRf>
Description
Obsolete command. Enter number of power sweeps for flat power correction. No query.
Cmd Parameters
<NRf>
Output
NA
Syntax Example
PSP <NRf>
PSP?
Description
Obsolete command. Output the number of power sweeps for flat power correction. No query.
Cmd Parameters
<NR1>
Output
<NR1>
Syntax Example
PSP?
PSPWR <NRf>
Description
Enter the Power Sweep Off value. No query.
Cmd Parameters
<NRf>
Output
NA
Syntax Example
PSPWR <NRf>
PSPWR?
Description
Output the Power Sweep Off value. No query.
Cmd Parameters
<NR3>
Output
<NR3>
Syntax Example
PSPWR?
PSTEP <NRf>
Description
Enter power sweep step size. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
PSTEP <NRf>
PSTEP?
Description
Enter power sweep step size. No query.
Cmd Parameters
NA
Output
<NR3>
Syntax Example
PSTEP?
PSTOP <NRf>
PSTOP?
Description
Enter power sweep stop power. Output power sweep stop power.
Cmd Parameters
<NRf>
Query Parameters
NA
Output
<NR3>
Syntax Example
PSTOP <NRf>
PSTOP?
PSTRT <NRf>
PSTRT?
Description
Enter power sweep start power. Output the power sweep start power.
Cmd Parameters
<NRf>
Query Parameters
NA
Output
<NR3>
Syntax Example
PSTRT <NRf>
PSTRT?
PSWC
Description
Perform power sweep linearity calibration. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
PSWS
PSWC0
Description
Turn power sweep linearity cal off. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
PSWC0
PSWC1
Description
Turn power sweep linearity cal on. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
PSWC1
PSWCX?
Description
Output power sweep linearity cal on/off status. No query.
Cmd Parameters
NA
Output
<NR1>
Syntax Example
PSWCX?
PSWP0
Description
Turn power sweep off. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
PSWP0
PSWP1
Description
Turn power sweep on. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
PSWP1
PSWPX?
Description
Query only. Output power sweep on/off status.
Cmd Parameters
NA
Output
<NR1>
Syntax Example
PSWPX?
PT0 <NRf>
Description
Set tabular printout points skipped to 0.
Parameters
NA
Output
NA
Syntax Example
PT0 <NRf>
PT1 <NRf>
Description
Set tabular printout points skipped to 1.
Parameters
NA
Output
NA
Syntax Example
PT1 <NRf>
PT2 <NRf>
Description
Set tabular printout points skipped to 2.
Parameters
NA
Output
NA
Syntax Example
PT2 <NRf>
PT3 <NRf>
Description
Set tabular printout points skipped to 3.
Parameters
NA
Output
NA
Syntax Example
PT3 <NRf>
PT4 <NRf>
Description
Set tabular printout points skipped to 4.
Parameters
NA
Output
NA
Syntax Example
PT4 <NRf>
PT5 <NRf>
Description
Set tabular printout points skipped to 5.
Parameters
NA
Output
NA
Syntax Example
PT5 <NRf>
PT6 <NRf>
Description
Set tabular printout points skipped to 6.
Parameters
NA
Output
NA
Syntax Example
PT6 <NRf>
PT7 <NRf>
Description
Set tabular printout points skipped to 7.
Parameters
NA
Output
NA
Syntax Example
PT7 <NRf>
PT8 <NRf>
Description
Set tabular printout points skipped to 8.
Parameters
NA
Output
NA
Syntax Example
PT8 <NRf>
PT9 <NRf>
Description
Set tabular printout points skipped to 9.
Parameters
NA
Output
NA
Syntax Example
PT9 <NRf>
PTAVG
Description
Set point-by-point averaging type. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
PTAVG
PTB
Description
Print tabular data for traces.
Parameters
NA
Output
NA
Syntax Example
PTB
PTBC
Description
Configure for printing tabular data for traces. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
PTBC
PTP <NRf>
PTP?
Description
Set the target power for flat test port power correction. Output the target power for flat test port power correction.
Cmd Parameters
<NRf>
Query Parameters
NA
Output
<NR3>
Syntax Example
PTP <NRf>
PTP?
PTS <NRf>
PTS?
Description
Set the number of points to be skipped for flat test port calibration. Output the number of points to be skipped for flat test port calibration.
Cmd Parameters
<NRf>
Query Parameters
NA
Output
<NR1>
Syntax Example
PTS <NRf>
PTS?
PTX?
Description
Output number of points to skip in tabular printout.
Parameters
<NR1>
Output
<NR1>
Syntax Example
PTX?
PW1 <NRf>
PW1?
Description
Set power level on external source1. Output power level on external source1.
Cmd Parameters
<NRf>
Query Parameters
NA
Output
<NR3>
Syntax Example
PW1 <NRf>
PW1?
PW2 <NRf>
PW2?
Description
Set power level on external source2. Output power level on external source2.
Cmd Parameters
<NRf>
Query Parameters
NA
Output
<NR3>
Syntax Example
PW2 <NRf>
PW2?
PWR <NRf>
PWR?
Description
Set the VNA power level. Output the VNA power level.
Cmd Parameters
<NRf>
Query Parameters
NA>
Output
<NR3>
Syntax Example
PWR <NRf>
PWR?
RC1
Description
Recall front panel setup data from memory location 1. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
RC1
RC10
Description
Recall front panel setup data from memory location 10. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
RC10
RC2
Description
Recall front panel setup data from memory location 2. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
RC2
RC3
Description
Recall front panel setup data from memory location 3. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
RC3
RC4
Description
Recall front panel setup data from memory location 4. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
RC4
RC5
Description
Recall front panel setup data from memory location 5. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
RC5
RC6
Description
Recall front panel setup data from memory location 6. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
RC6
RC7
Description
Recall front panel setup data from memory location 7. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
RC7
RC8
Description
Recall front panel setup data from memory location 8. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
RC8
RC9
Description
Recall front panel setup data from memory location 9. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
RC9
RCKH <string>
Description
Recall trace memory file from hard disk. No query.
Parameters
<string>
Output
NA
Syntax Example
RCKH <string>
RCLCALH <string>
Description
Recall calibration/front panel setup from hard disk. No query.
Cmd Parameters
<string>
Output
NA
Syntax Example
RCLCALH <string>
RCLNRMH <string>
Description
Recall trace memory file from hard disk. No query.
Parameters
<string>
Output
NA
Syntax Example
RCLNRMH <string>
RD <string>
Description
Remove a disk directory or a memory card directory. No query.
Cmd Parameters
NA
Output
<string>
Syntax Example
RD <string>
RDA
Description
Select automatic reference delay calculation. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
RDA
RDD <NRf>
RDD?
Description
Enter reference delay in distance for active channel. Output reference delay in distance for active channel.
Cmd Parameters
<NRf>
Query Parameters
NA
Output
<NR3>
Syntax Example
RDD <NRf>
RDD?
RDT <NRf>
Description
Enter reference delay in time for active channel. No query.
Cmd Parameters
NA
Output
<NRf>
Syntax Example
RDT <NRf>
RDT?
Description
Output reference delay in time for active channel. No query.
Cmd Parameters
<NR3>
Output
<NR3>
Syntax Example
RDT?
RECALL <string>
Description
Recall various kinds of system files. No query.
Cmd Parameters
NA
Output
<string>
Syntax Example
RECALL <string>
REF <NRf>
Description
Enter reference line for top graph of active trace. No query.
Cmd Parameters
NA
Output
<NRf>
Syntax Example
REF <NRf>
REF?
Description
Query only. Output reference line for top graph of active trace.
Cmd Parameters
<NR1>
Output
<NR1>
Syntax Example
REF?
REF2 <NRf>
Description
Enter reference line for top graph of active trace. No query.
Cmd Parameters
<NR1>
Output
NA
Syntax Example
REF2 <NRf>
REF2?
Description
Query only. Output reference line for top graph of active trace
Cmd Parameters
NA
Output
<NR1>
Syntax Example
REF2?
REL
Description
Select Real display for the active trace. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
REL
RGZ
Description
Select reflective device greater than Z0 in LRL calibration. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
RGZ
RH0
Description
Turn RF off while in hold. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
RH0
RH1
Description
Leave RF on while in hold. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
RH1
RHX?
Description
Query only. Output RF on/off while in hold status.
Cmd Parameters
NA
Output
<NR1>
Where:
• 0 for Off
• 1 for On
Syntax Example
RHX?
RIM
Description
Select Real and Imaginary display for the active trace. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
RIM
RL
Description
Send all devices to Local. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
RL
RLDH <string>
Description
Recall calibration/front panel setup from hard disk file or from memory card file. No query.
Cmd Parameters
<string>
Output
NA
Syntax Example
RLDH <string>
RLZ
Description
Select reflective device less than Z0 in LRL calibration. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
RLZ
RM1
Description
Select reference plane at line 1 midpoint for LRL calibration. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
RM1
RMX?
Description
Query only. Output reference plane location for LRL calibration.
Cmd Parameters
<NR1>
Output
<NR1>
Syntax Example
RMX?
ROL <NRf>
ROL?
Description
Set reflective device offset length. Output reflective device offset length.
Cmd Parameters
<NRf>
Query Parameters
NA
Output
<NR3>
Syntax Example
ROL <NRf>
ROL?
RPC
Description
Repeat previous calibration. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
RPC
RPO <NRf>
RPO?
Description
Enter rear panel DC voltage value. Output rear panel DC voltage value.
Cmd Parameters
<NRf>
Query Parameters
NA
Output
<NR3>
Syntax Example
RPO <NRf>
RPO?
RRP
Description
Select reference plane at reflection plane for LRL calibration. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
RRP
RST
Description
Instrument reset. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
RST
RST0
Description
Instrument reset. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
RST0
RST1
Description
Instrument reset. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
RST1
RSTAVG
Description
Reset the averaging sweep count. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
RSTAVG
RSTGC
Description
Reset gain compression Cmd Parameters to default. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
RSTGC
RT0
Description
Turn retrace RF off. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
RT0
RT1
Description
Turn retrace RF on. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
RT1
RTL
Description
Send all devices to Local. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
RTL
RTX?
Description
Query only. Output retrace RF on/off status.
Cmd Parameters
<NR1>
Output
<NR1>
Syntax Example
RTX?
RV0
Description
Turn rear panel output voltage off. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
RV0
RV1
RV1?
Description
Turn rear panel output voltage on. Output rear panel output voltage on/off status
Cmd Parameters
NA
Query Parameters
NA
Output
<NR1> 0|1
Where:
• 0 for Off
• 1 for On
Syntax Example
RV1
RV1?
RVD
Description
Set rear panel output mode to DC value. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
RVD
RVH
Description
Set rear panel output mode to horizontal. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
RVH
RVL
Description
Set rear panel output mode to lock direction. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
RVL
RVX?
Description
Query only. Output rear panel output mode.
Query Parameters
NA
Output
<NR1> 1|2|3|4
Where:
• 1 for horizontal
• 2 for vertical
• 3 for lock direction
• 4 for DC output
Syntax Example
RVX?
RXZ?
Description
Query only. Output reflective device in LRL calibration greater/less than Z0.
Cmd Parameters
<NR1>
Output
<NR1>
Syntax Example
RXZ?
S11
Description
Measure S11 on active trace. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
S11
S12
Description
Measure S12 on active trace. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
S12
S21
Description
Measure S21 on active trace. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
S21
S22
Description
Measure S22 on active trace. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
S22
SA1 <NRf>
SA1?
Description
Set reference attenuator value on port 1. Output reference attenuator value on port 1.
Cmd Parameters
<NRf>
Query Parameters
NA
Output
<NR1>
Syntax Example
SA1 <NRf>
SA1?
SA1MAX?
Description
Query only. Output Port 1 reference attenuator maximum value.
Query Parameters
NA
Output
<NR1>
Syntax Example
SA1MAX?
SA2 <NRf>
SA2?
Description
Set reference attenuator value on port 2. Output reference attenuator value on port 2.
Cmd Parameters
<NRf>
Query Parameters
NA
Output
<NR1>
Syntax Example
SA2 <NRf>
SA2?
SAMP?
Description
Query only. Output the number of samplers used for measurements.
Query Parameters
NA
Output
<NR1>
Syntax Example
SAMP?
SAMP2
Description
Use 2 samplers for measurements. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
SAMP2
SAMP3
Description
Use 3 samplers for measurements. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
SAMP3
SAVCALH <string>
Description
Save calibration/front panel setup to hard disk or memory card. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
SAVCALH <string>
SAVDATH <string>
Description
Save tabular data to hard disk or memory card. No query.
Cmd Parameters
<string>
Output
NA
Syntax Example
SAVDATH <string>
SAVE <string>
Description
Save a data file to disk or memory card. No query.
Cmd Parameters
<string>
Output
NA
Syntax Example
SAVE <string>
SAVEGC <string>
Description
Save text format gain compression data to disk or memory card. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
SAVEGC <string>
SAVELGH <string>
Description
Save error list to hard disk or memory card. No query.
Cmd Parameters
<string>
Output
NA
Syntax Example
SAVELGH <string>
SAVLOGH <string>
Description
Save service log to hard disk or memory card. No query.
Cmd Parameters
<string>
Output
NA
Syntax Example
SAVLOGH <string>
SAVNRMH <string>
Description
Save trace memory to hard disk. No query.
Parameters
<string>
Output
NA
Syntax Example
SAVNRMH <string>
SBD <NRf>
SBD?
Description
Enter substrate dielectric for microstrip calibration. Output substrate dielectric for microstrip calibration
Cmd Parameters
<NRf>
Query Parameters
NA
Output
<NR3>
Syntax Example
SBD <NRf>
SBD?
SBT <NRf>
SBT?
Description
Enter substrate thickness for microstrip calibration. Output substrate thickness for microstrip calibration.
Cmd Parameters
<NRf>
Query Parameters
NA
Output
<NR3>
Syntax Example
SBT <NRf>
SBT?
SCL <NRf>
SCL?
Description
Enter Scale Resolution for top graph of active trace. Output Scale Resolution for top graph of active trace.
Cmd Parameters
<NRf>
Query Parameters
NA
Output
<NR3>
Syntax Example
SCL <NRf>
SCL?
SCL2 <NRf>
SCL2?
Description
Enter Scale Resolution for bottom graph of active trace. Output Scale Resolution for bottom graph of active trace.
Cmd Parameters
<NRf>
Query Parameters
NA
Output
<NR3>
Syntax Example
SCL2 <NRf>
SCL2?
SCM
Description
Select Standard (SOLT) calibration method. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
SCM
SDKH <string>
Description
Save trace memory to hard disk. No query.
Parameters
<string>
Output
NA
Syntax Example
SDKH <string>
SELBB
Description
Select BroadBand (Panorama) test set operation on the active channel. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
SELBB
SELINT
Description
Select internal (normal) test set operation on the active channel. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
SELINT
SELMM
Description
Select Millimeter Wave test set operation on the active channel. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
SELMM
SELXX?
Description
Query only. Output test set selection to Internal, MMWave, or BroadBand.
Query Parameters
NA
Output
<NR1> 0|1|2|3
Where:
• 0 is internal
• 1 is millimeter wave
• 2 is S-parameter
• 3 is Broadband
Syntax Example
SELXX?
SETPMA
Description
Programs the power meter to use channel A. No query.
Parameters
NA
Output
NA
Syntax Example
SETPMA
SETPMB
Description
Programs the power meter to use channel B. No query.
Parameters
NA
Output
NA
Syntax Example
SETPMB
SETUP
Description
Display the SETUP menu. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
SETUP
SFC
Description
Perform a flat test port power correction. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
SFC
SFGCA
Description
Select swept frequency gain compression application. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
SFGCA
SFGCT
Description
Start swept frequency gain compression test. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
SFGCT
SH1 <NRf>
SH1?
Description
Enter offset length for Short1 for user-specified connector. Output offset length for Short 1 for user-specified connector.
Cmd Parameters
<NRf>
Query Parameters
NA
Output
<NR3>
Syntax Example
SH1 <NRf>
SH1?
SH2 <NRf>
SH2?
Description
Enter offset length for Short 2 for user-specified connector. Output offset length for Short 2 for user-specified connector.
Cmd Parameters
<NRf>
Query Parameters
NA
Output
<NR3>
Syntax Example
SH2 <NRf>
SH2?
SLC
Description
Clear all segmented limits definition. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
SLC
SLD
Description
Select sliding load for calibration. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
SLD
SLL0
Description
Turn lower segmented limits display off. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
SLL0
SLL1
Description
Turn lower segmented limits display on. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
SLL1
SLLX?
Description
Query only. Output lower segmented limits display on/off status on active channel.
Query Parameters
NA
Output
<NR1> 0|1
Where:
• 0 for Off
• 1 for On
Syntax Example
SLLX?
SLU0
Description
Turn upper segmented limits display off. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
SLU0
SLU1
Description
Turn upper segmented limits display on. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
SLU1
SLUX?
Description
Query only. Output upper segmented limits display on/off status on active channel
Query Parameters
NA
Output
<NR1> 0|1
Where:
• 0 for Off
• 1 for On
Syntax Example
SLUX?
SMC <NRf>
Description
Enter scale and select compressed Smith chart display. No query.
Cmd Parameters
NA
Output
<NRf>
Syntax Example
SMC <NRf>
SME <NRf>
Description
Enter scale and select expanded Smith chart display. No query.
Cmd Parameters
NA
Output
<NRf>
Syntax Example
SME <NRf>
SMI
Description
Select Smith Chart display for the active trace. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
SMI
SMO
Description
Turn smoothing on. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
SMO
SNPDB
Description
Set the S2P file parameter format to Log Magnitude and Phase. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
SNPDB
SNPFMTX?
Description
Query only. Output the S2P file frequency format
Cmd Parameters
<NR1>
Output
<NR1>
Syntax Example
SNPFMTX?
SNPGHZ
Description
Set the S2P file frequency format to GHz. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
SNPGHZ
SNPHZ
Description
Set the S2P file frequency format to Hz. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
SNPHZ
SNPKHZ
Description
Set the S2P file frequency format to kHz. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
SNPKHZ
SNPMA
Description
Set the S2P file parameter format to Linear Magnitude and Phase. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
SNPMA
SNPMHZ
Description
Set the S2P file frequency format to MHz. No query.
Cmd Parameters
NA
Output
NA
Syntax Example
SNPMHZ
SNPRI
Description
Set the S2P file parameter format to Real and Imaginary. No query.