VectorStar™ MS464xB Series Microwave Vector Network Analyzer User Interface Reference : System Menus : Preset Menus and Dialog Boxes
 
Preset Menus and Dialog Boxes
PRESET SETUP Menu
Use the PRESET SETUP menu to define which previously saved preset configuration file will be applied to the instrument.
PRESET SETUP Menu Button Selection Group
The Default, Default 0, and Saved Setup buttons form a three-button selection group where selecting one button deselects the other two buttons.
Previous
SETUP Menu
Navigation
MAIN | System | SYSTEM | Setup | SETUP | Preset Setup | PRESET SETUP
PRESET SETUP Menu 
Preset Actions
The selected Default or Saved Setup presets (described below) are invoked by any of the following:
Preset Key
MENU BAR | Utilities | Preset
Default
If selected, Default selection loads the factory as-shipped preset configuration which is one channel with four traces displayed on a two-row and two-column trace display. This preset option is always available. Once this option is selected, if the user presses the front panel Preset Key or selects MENU BAR | Utilities | Preset, the instrument returns to the factory as-shipped configuration.
Default 0
The Default 0 button operates identical to the Default button (above) with the addition removing any Cal Kits and/or Characterization Coefficient files from instrument memory. Once used, all connector coefficients are then returned to the factory as-shipped default values. Note that any Cal Kit and/or Characterization Coefficient files resident on the instrument hard drive are not deleted and remain in place. If this command is used, the user must re-load into memory all required Cal Kit and other Characterization Coefficient files.
Saved Setup
If selected, the Saved Setup selection loads the setup file selected in the dialog box below. Once selected, if either of the preset actions (described above) occur, the preset file returns the instrument to the user-defined configuration.
If the Saved Setup button is clicked when no prior Setup File has been saved, a NO FILE SELECTED dialog box appears with the message: “There is currently no saved setup selected. This selection requires a file selection. Would you like to select the file now?”
Click OK to open the SELECT PRESET SETUP dialog box described below.
Click CANCEL to close the dialog box.
Select Saved Setup File
Select displays the SELECT PRESET SETUP dialog box where a previously saved setup configuration file is be selected. Once a file is selected, the Saved Setup button must be selected to implement the configuration from the:
Preset Key
MENU BAR | Utilities | Preset
SELECT PRESET SETUP Dialog Box
SELECT PRESET SETUP Dialog Box
Previous
PRESET SETUP Menu
Navigation
MAIN | System | SYSTEM | Setup | SETUP | Preset Setup | PRESET SETUP | Saved Setup | SELECT PRESET SETUP Dialog Box
SELECT PRESET SETUP Dialog Box
Allows the user to select a previously saved All Channel Setup CHA file. Navigate to the saved CHA file, select it, and then click Open to use the file. Click Cancel to cancel the operation.
POWER-ON SETUP Menu
The POWER-ON SETUP menu defines in which configuration the instrument will restore to after a cold start and full power-up. In order to use the Saved Setup option, a previously stored power-up setup file must have been saved using the menu bar Save Setup command.
Menu Bar
MENU BAR | File Drop-Down Menu
Previous
SETUP Menu
Navigation
MAIN | System | SYSTEM | Setup | SETUP | Power-On Setup | POWER-ON SETUP
POWER-ON SETUP Menu 
 
POWER-ON SETUP Menu Button Selection Group
The Default, Last Setup, and Select Saved Setup File buttons form a button selection group where only one (1) of the three buttons may be selected. Once selected, the power-on setting remains until changed.
Default
Select sets the factory default as-shipped power-on setup settings. This setting is always available.
Last Setup
For many users in general purpose work, this setting is the user-selected default. Select sets the power-on setup to be from the last operational state including frequencies, channels, traces, markers, and limit lines.
 
Saved Setup
Select sets the power-on settings to a previously saved user-defined setup file, useful for repeated identical settings in a line production mode. Using the button described below, a previously-saved setting file can be recalled and will remain active until changed. The system can store multiple setup files but only one can be active at any time.
If the Saved Setup button is clicked when no prior Setup File has been saved, a NO FILE SELECTED dialog box appears with the message: “There is currently no saved setup selected. This selection requires a file selection. Would you like to select the file now?”
Click OK to open the SELECT USER SETUP FILE (CHA FILE) dialog box described below.
Click CANCEL to close the dialog box.
Select Saved Setup File
Use this button to display a dialog to recall a previously saved setup file. Once recalled, the file settings can be implemented by selecting the Saved Setup button above. Select displays the SELECT USER SETUP FILE dialog box.
SELECT USER SETUP FILE (CHA) Dialog Box
SELECT USER SETUP FILE (CHA) Dialog Box
Use the SELECT USER SETUP FILE dialog to select a previously saved power-on setup file for use on the POWER-ON SETUP menu.
Previous
POWER-ON SETUP Menu
Navigation
MAIN | System | SYSTEM | Setup | SETUP | Power-On Setup | POWER-ON SETUP | Saved Setup | SELECT USER SETUP FILE (CHA) Dialog Box
SELECT USER SETUP FILE (CHA) Dialog Box
Instructions
Use this dialog to select a previously stored power-on setup configuration file.
1. Navigate to the POWER-ON SETUP menu.
MAIN | System | SYSTEM | Setup | SETUP | Power-On Setup | POWER-ON SETUP | Select Saved Setup File
2. The Select User Setup File dialog box appears.
3. Navigate to the required folder and locate the required All Channel Setup (.CHA) file.
Best practices recommend the C:\AnritsuVNA folder.
4. Once the appropriate file is selected, click Open.
5. The selected power-on setup file is now available for use on the POWER-ON SETUP menu if the Saved Setup button is selected.
POWER-ON SETUP Menu